Match the correct standard
Keep the enquiry aligned with the actual product form and intended service.
Manufactured in Gujarat · India-wide supply · Export enquiries
C12200 Copper Tubes Manufacturer in India
Specification-led c12200 copper tubes supplied against grade, standard, dimensions, condition, testing and delivery requirements.
Primary specificationASTM B75 · B88 · B280 · EN 1057GradeUNS C12200 · Cu-DHP · CW024ASupply range6–267 mm OD · 0.30–20 mm wallDocumentationEN 10204 3.1 by confirmation
Specification-led copper supply
Define the product before comparing price and delivery.
C12200 Copper Tubes should be purchased against a complete material and dimensional requirement. Product names alone do not define grade, tolerance, condition, testing or suitability.
C12200 identifies the alloy. The finished product standard controls dimensions, temper, cleanliness, testing and permitted application.
A clearer route to purchase
Reduce specification gaps before issuing the order.
Define dimensions clearly
State every controlling dimension, tolerance, length and quantity.
Plan evidence early
Identify certificates, tests, marking and inspection before commercial review.
Configure it visually
Use the 3D builder to organise the product and purchasing information.
Technical specification
Published product reference
Final combinations and compliance are confirmed against the accepted quotation, current standard edition and purchase specification.
Do not use this summary as a substitute for the governing standard, design calculation or approved project specification.
3D product configuration
Prepare a more complete enquiry.
Open the builder with C12200 Copper Tubes selected, then send the grade, standard, dimensions, form, condition, quantity, inspection and destination for review.
Product identity
Grade, standard and intended service.
Manufacturing definition
Dimensions, tolerance, condition and finish.
Order scope
Quantity, documents, inspection, packing and destination.
Selection by service
Applications reviewed against the complete requirement
Water and plumbing tube
Selection is confirmed against the service conditions, governing standard and buyer specification.
ACR and refrigeration tube
Selection is confirmed against the service conditions, governing standard and buyer specification.
General engineering
Selection is confirmed against the service conditions, governing standard and buyer specification.
Heat-transfer and fabricated components
Selection is confirmed against the service conditions, governing standard and buyer specification.
Engineering note
Application names do not establish suitability. Confirm loads, medium, temperature, pressure or electrical duty, fabrication process, environment and governing code as applicable.
UNS C12200 and Cu-DHP tube
Specify the finished tube standard as well as the copper grade.
C12200 seamless tubing
UNS C12200 identifies phosphorus-deoxidised copper. The applicable finished-product standard still controls dimensions, temper and testing.
Annealed C12200 tube
For soft copper tube or coil, state the required temper, OD, wall, coil form, length, cleanliness and end protection.
Hard-drawn C12200 tube
For straight tube, identify temper, length, straightness, tolerances and the fabrication process that follows delivery.
Application-specific standards
ASTM B280, ASTM B88 and other tube standards are not interchangeable simply because each order may use C12200 copper.
Choose by service
Continue to the dedicated ASTM B280, ASTM B88 or general engineering page where that requirement governs.
Quality and order definition
Make the purchase specification traceable.
State the certificate, test plan, marking, inspection hold points and acceptance criteria before quotation.
View quality and testing capabilities →- 01
MaterialGrade and standard
- 02
DimensionsSize, tolerances and length
- 03
ConditionTemper, form, finish and ends
- 04
EvidenceMTC, tests and inspection
- 05
DeliveryQuantity, packing and destination
Before requesting a quotation
Frequently asked questions about C12200 Copper Tubes
What information is needed for a quotation?+
Provide grade, standard, dimensions, tolerances, condition, quantity, certificates, inspection and destination.
Can custom dimensions be reviewed?+
Yes, subject to product form, tooling, tolerances, grade, quantity and manufacturing feasibility. Attach a drawing where dimensions are not standard.
Is EN 10204 3.1 documentation available?+
It may be specified where supported by the order. State the certificate and any third-party inspection requirement in the original RFQ.
Can I configure this product in the 3D builder?+
Yes. Open the 3D product builder with C12200 Copper Tubes selected and send the result for technical review.
C12200 Copper Tubes enquiry
Get a quotation matched to the actual requirement.
Send the standard, grade, dimensions, condition, quantity, inspection and destination.
Available manufacturing and documentation scope is confirmed before order acceptance.